hobbit-clients.cfg not recognizing DISK /autoyast IGNORE
I'm having an issue w/ hobbit-clients.cfg not working w/ DISK /xxxx
IGNORE...
I've tried the following, none of which end up ignoring /autoyast....
Anybody have any ideas?
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK %^\/autoyas* IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK /autoyast IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
HOST=nyxx-pil-dma02dr PROC postgres 1 DISK /autoyast IGNORE
OR
HOST=nyse-pil-dma02dr PROC postgres 1 DISK %^\/autoyas* IGNORE
Thanks,
Rolf Brusletto
DISK %^/autoyas.* IGNORE
-----Original Message----- From: Rolf Brusletto [mailto:rbrusletto at selero.com] Sent: Tuesday, August 26, 2008 15:47 To: hobbit at hswn.dk Subject: [hobbit] hobbit-clients.cfg not recognizing DISK /autoyast IGNORE
I'm having an issue w/ hobbit-clients.cfg not working w/ DISK /xxxx
IGNORE...
I've tried the following, none of which end up ignoring /autoyast....
Anybody have any ideas?
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK %^\/autoyas* IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK /autoyast IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
HOST=nyxx-pil-dma02dr PROC postgres 1 DISK /autoyast IGNORE
OR
HOST=nyse-pil-dma02dr PROC postgres 1 DISK %^\/autoyas* IGNORE
Thanks,
Rolf Brusletto
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
I had tried this, with no luck as well... Forgot to mention I'm
running 4.2.0 server and clients..
On Aug 26, 2008, at 1:51 PM, Eric Meddaugh wrote:
DISK %^/autoyas.* IGNORE
-----Original Message----- From: Rolf Brusletto [mailto:rbrusletto at selero.com] Sent: Tuesday, August 26, 2008 15:47 To: hobbit at hswn.dk Subject: [hobbit] hobbit-clients.cfg not recognizing DISK /autoyast IGNORE
I'm having an issue w/ hobbit-clients.cfg not working w/ DISK /xxxx IGNORE...
I've tried the following, none of which end up ignoring /autoyast....
Anybody have any ideas?
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK %^\/autoyas* IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK /autoyast IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
HOST=nyxx-pil-dma02dr PROC postgres 1 DISK /autoyast IGNORE
OR
HOST=nyse-pil-dma02dr PROC postgres 1 DISK %^\/autoyas* IGNORE
Thanks,
Rolf Brusletto
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
Regards,
Rolf Brusletto Selero, Inc Senior Network Engineer O: 303.914.2807 C: 303.638.8013 E: rbrusletto at Selero.com
That's the line we use in our configs and it works great:
DISK %^/home/.* IGNORE
That ignores all our auto_home entries on solaris.
---Eric
-----Original Message----- From: Rolf Brusletto [mailto:rbrusletto at selero.com] Sent: Tuesday, August 26, 2008 15:58 To: hobbit at hswn.dk Subject: Re: [hobbit] hobbit-clients.cfg not recognizing DISK /autoyast IGNORE
I had tried this, with no luck as well... Forgot to mention I'm
running 4.2.0 server and clients..
On Aug 26, 2008, at 1:51 PM, Eric Meddaugh wrote:
DISK %^/autoyas.* IGNORE
-----Original Message----- From: Rolf Brusletto [mailto:rbrusletto at selero.com] Sent: Tuesday, August 26, 2008 15:47 To: hobbit at hswn.dk Subject: [hobbit] hobbit-clients.cfg not recognizing DISK /autoyast IGNORE
I'm having an issue w/ hobbit-clients.cfg not working w/ DISK /xxxx IGNORE...
I've tried the following, none of which end up ignoring /autoyast....
Anybody have any ideas?
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK %^\/autoyas* IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK /autoyast IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
HOST=nyxx-pil-dma02dr PROC postgres 1 DISK /autoyast IGNORE
OR
HOST=nyse-pil-dma02dr PROC postgres 1 DISK %^\/autoyas* IGNORE
Thanks,
Rolf Brusletto
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
Regards,
Rolf Brusletto Selero, Inc Senior Network Engineer O: 303.914.2807 C: 303.638.8013 E: rbrusletto at Selero.com
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
Thanks... hobbit server doesn't need to be restarted does it ?
On Aug 26, 2008, at 2:00 PM, Eric Meddaugh wrote:
That's the line we use in our configs and it works great:
DISK %^/home/.* IGNOREThat ignores all our auto_home entries on solaris.
---Eric
-----Original Message----- From: Rolf Brusletto [mailto:rbrusletto at selero.com] Sent: Tuesday, August 26, 2008 15:58 To: hobbit at hswn.dk Subject: Re: [hobbit] hobbit-clients.cfg not recognizing DISK / autoyast IGNORE
I had tried this, with no luck as well... Forgot to mention I'm running 4.2.0 server and clients..
On Aug 26, 2008, at 1:51 PM, Eric Meddaugh wrote:
DISK %^/autoyas.* IGNORE
-----Original Message----- From: Rolf Brusletto [mailto:rbrusletto at selero.com] Sent: Tuesday, August 26, 2008 15:47 To: hobbit at hswn.dk Subject: [hobbit] hobbit-clients.cfg not recognizing DISK /autoyast IGNORE
I'm having an issue w/ hobbit-clients.cfg not working w/ DISK /xxxx IGNORE...
I've tried the following, none of which end up ignoring /autoyast....
Anybody have any ideas?
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK %^\/autoyas* IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK /autoyast IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
HOST=nyxx-pil-dma02dr PROC postgres 1 DISK /autoyast IGNORE
OR
HOST=nyse-pil-dma02dr PROC postgres 1 DISK %^\/autoyas* IGNORE
Thanks,
Rolf Brusletto
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
Regards,
Rolf Brusletto Selero, Inc Senior Network Engineer O: 303.914.2807 C: 303.638.8013 E: rbrusletto at Selero.com
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
Regards,
Rolf Brusletto Selero, Inc Senior Network Engineer O: 303.914.2807 C: 303.638.8013 E: rbrusletto at Selero.com
It usually picks it up, sometimes we do a "reload", other times we've just restart it. I don't think anything is needed for it to reread the file.
-----Original Message----- From: Rolf Brusletto [mailto:rbrusletto at selero.com] Sent: Tuesday, August 26, 2008 16:09 To: hobbit at hswn.dk Subject: Re: [hobbit] hobbit-clients.cfg not recognizing DISK /autoyast IGNORE
Thanks... hobbit server doesn't need to be restarted does it ?
On Aug 26, 2008, at 2:00 PM, Eric Meddaugh wrote:
That's the line we use in our configs and it works great:
DISK %^/home/.* IGNOREThat ignores all our auto_home entries on solaris.
---Eric
-----Original Message----- From: Rolf Brusletto [mailto:rbrusletto at selero.com] Sent: Tuesday, August 26, 2008 15:58 To: hobbit at hswn.dk Subject: Re: [hobbit] hobbit-clients.cfg not recognizing DISK / autoyast IGNORE
I had tried this, with no luck as well... Forgot to mention I'm running 4.2.0 server and clients..
On Aug 26, 2008, at 1:51 PM, Eric Meddaugh wrote:
DISK %^/autoyas.* IGNORE
-----Original Message----- From: Rolf Brusletto [mailto:rbrusletto at selero.com] Sent: Tuesday, August 26, 2008 15:47 To: hobbit at hswn.dk Subject: [hobbit] hobbit-clients.cfg not recognizing DISK /autoyast IGNORE
I'm having an issue w/ hobbit-clients.cfg not working w/ DISK /xxxx IGNORE...
I've tried the following, none of which end up ignoring /autoyast....
Anybody have any ideas?
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK %^\/autoyas* IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK /autoyast IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
HOST=nyxx-pil-dma02dr PROC postgres 1 DISK /autoyast IGNORE
OR
HOST=nyse-pil-dma02dr PROC postgres 1 DISK %^\/autoyas* IGNORE
Thanks,
Rolf Brusletto
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
Regards,
Rolf Brusletto Selero, Inc Senior Network Engineer O: 303.914.2807 C: 303.638.8013 E: rbrusletto at Selero.com
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
Regards,
Rolf Brusletto Selero, Inc Senior Network Engineer O: 303.914.2807 C: 303.638.8013 E: rbrusletto at Selero.com
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
Maybe this is to obvious but it bit my rear; be sure that your DEFAULT lines are at the bottom of the file.
Robert
-----Original Message----- From: Eric Meddaugh [mailto:etmsys at rit.edu] Sent: Tuesday, August 26, 2008 4:01 PM To: hobbit at hswn.dk Subject: RE: [hobbit] hobbit-clients.cfg not recognizing DISK /autoyast IGNORE
That's the line we use in our configs and it works great:
DISK %^/home/.* IGNOREThat ignores all our auto_home entries on solaris.
---Eric
-----Original Message----- From: Rolf Brusletto [mailto:rbrusletto at selero.com] Sent: Tuesday, August 26, 2008 15:58 To: hobbit at hswn.dk Subject: Re: [hobbit] hobbit-clients.cfg not recognizing DISK /autoyast IGNORE
I had tried this, with no luck as well... Forgot to mention I'm running 4.2.0 server and clients..
On Aug 26, 2008, at 1:51 PM, Eric Meddaugh wrote:
DISK %^/autoyas.* IGNORE
-----Original Message----- From: Rolf Brusletto [mailto:rbrusletto at selero.com] Sent: Tuesday, August 26, 2008 15:47 To: hobbit at hswn.dk Subject: [hobbit] hobbit-clients.cfg not recognizing DISK /autoyast IGNORE
I'm having an issue w/ hobbit-clients.cfg not working w/ DISK /xxxx IGNORE...
I've tried the following, none of which end up ignoring /autoyast....
Anybody have any ideas?
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK %^\/autoyas* IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK /autoyast IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
HOST=nyxx-pil-dma02dr PROC postgres 1 DISK /autoyast IGNORE
OR
HOST=nyse-pil-dma02dr PROC postgres 1 DISK %^\/autoyas* IGNORE
Thanks,
Rolf Brusletto
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
Regards,
Rolf Brusletto Selero, Inc Senior Network Engineer O: 303.914.2807 C: 303.638.8013 E: rbrusletto at Selero.com
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
Thank you sir!
I missed this.... integral part of the documentation IN the hobbit-
clients.cfg file as well. Put the defaults at the bottom and
everything works!
Cheers
On Aug 26, 2008, at 3:20 PM, McGraw, Robert P wrote:
Maybe this is to obvious but it bit my rear; be sure that your
DEFAULT lines are at the bottom of the file.Robert
-----Original Message----- From: Eric Meddaugh [mailto:etmsys at rit.edu] Sent: Tuesday, August 26, 2008 4:01 PM To: hobbit at hswn.dk Subject: RE: [hobbit] hobbit-clients.cfg not recognizing DISK / autoyast IGNORE
That's the line we use in our configs and it works great:
DISK %^/home/.* IGNOREThat ignores all our auto_home entries on solaris.
---Eric
-----Original Message----- From: Rolf Brusletto [mailto:rbrusletto at selero.com] Sent: Tuesday, August 26, 2008 15:58 To: hobbit at hswn.dk Subject: Re: [hobbit] hobbit-clients.cfg not recognizing DISK / autoyast IGNORE
I had tried this, with no luck as well... Forgot to mention I'm running 4.2.0 server and clients..
On Aug 26, 2008, at 1:51 PM, Eric Meddaugh wrote:
DISK %^/autoyas.* IGNORE
-----Original Message----- From: Rolf Brusletto [mailto:rbrusletto at selero.com] Sent: Tuesday, August 26, 2008 15:47 To: hobbit at hswn.dk Subject: [hobbit] hobbit-clients.cfg not recognizing DISK /autoyast IGNORE
I'm having an issue w/ hobbit-clients.cfg not working w/ DISK /xxxx IGNORE...
I've tried the following, none of which end up ignoring / autoyast....
Anybody have any ideas?
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK %^\/autoyas* IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK /autoyast IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
HOST=nyxx-pil-dma02dr PROC postgres 1 DISK /autoyast IGNORE
OR
HOST=nyse-pil-dma02dr PROC postgres 1 DISK %^\/autoyas* IGNORE
Thanks,
Rolf Brusletto
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
Just a point, but remember that the * directive ignores everything below it DISK * 90 95 DISK %^\/autoyas* IGNORE
put the "DISK * 90 95" line last.
2008/8/26 Rolf Brusletto <rbrusletto at selero.com>
I'm having an issue w/ hobbit-clients.cfg not working w/ DISK /xxxx IGNORE...
I've tried the following, none of which end up ignoring /autoyast....
Anybody have any ideas?
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK %^\/autoyas* IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK /autoyast IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
HOST=nyxx-pil-dma02dr PROC postgres 1 DISK /autoyast IGNORE
OR
HOST=nyse-pil-dma02dr PROC postgres 1 DISK %^\/autoyas* IGNORE
Thanks,
Rolf Brusletto
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
Thanks!
On Aug 26, 2008, at 3:32 PM, Stefan wrote:
Just a point, but remember that the * directive ignores everything
below it DISK * 90 95 DISK %^\/autoyas* IGNOREput the "DISK * 90 95" line last.
2008/8/26 Rolf Brusletto <rbrusletto at selero.com> I'm having an issue w/ hobbit-clients.cfg not working w/ DISK /xxxx
IGNORE...I've tried the following, none of which end up ignoring /autoyast....
Anybody have any ideas?
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK %^\/autoyas* IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
DEFAULT # These are the built-in defaults. UP 1h LOAD 5.0 10.0 DISK * 90 95 DISK /autoyast IGNORE MEMPHYS 100 101 MEMSWAP 50 80 MEMACT 90 97 PROC ntpd 1
OR
HOST=nyxx-pil-dma02dr PROC postgres 1 DISK /autoyast IGNORE
OR
HOST=nyse-pil-dma02dr PROC postgres 1 DISK %^\/autoyas* IGNORE
Thanks,
Rolf Brusletto
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
Regards,
Rolf Brusletto Selero, Inc Senior Network Engineer O: 303.914.2807 C: 303.638.8013 E: rbrusletto at Selero.com
Dear ladies and gentlemen,
momentanely I´am working on a concept for monitoring tools which compares some montitoring tools in regard of the requirements of our company.
Can you tell me if the following requirements will be fulfilled by your tool?
(1) Open Source Solution (2) Big community is available (3) Documentation is at a high quality (4) Tool is easy to operate (5) The Tool configuration is easy (6) HMI configuration is easy (7) Background pictures can be implementet (8) Support of SNMP v1,v2,v3 (9) It is possible to call scripts (shell scripts, perl scripts and so on) (10) Definition of roles possible (11) Processing of Traps possible (12) Tool shall be extendable (13) Longtime-monitoring shall be possible.
Please can you checkmark these items?
I create a list with a lot of features for the tools but unfortunately have some open points also for your tool BigSister.
So I would ask you if you can make checkmarks to the open features if your tool will fulfill the features. Here they are:
Alert-Form (mail, SMS, pager,?.)History of generated Status changes displayable/archieveableLogging and Display of Performance dataProtocolls (snmp, ssh,?)
NetApp?HW support like VMWare, Cisco, Juniper, F5, Veritas, Nortel, EMC,Support of geographic network mapsredundancy by starting multiple instances possibleReal-time diagnosisLocal tests by installing application on a clienthistory and reportsflexibility: Def. of alarm thresholds and warning, HMI adaptableUser managementlongterm monitoringAvailibility reportVirtualisation possibleTemplates availableXML-Data-Import / ExportApplication load distribution on multiple hostsIntegration of failure and performance monitoring
Can you return the answer to my e-mail-account please?
In hope of a quick answer I send you many regards,
I need this information urgently because I have to finish the concept on friday
Many regards,
DFS Deutsche Flugsicherung GmbH Am DFS-Campus 10 D - 63225 Langen
Tel.: +49-(0)6103-707-0
Sitz der Gesellschaft: Langen/Hessen Zuständiges Registergericht: AG Offenbach am Main, HRB 34977 Vorsitzender des Aufsichtsrates: Robert Scholl Geschäftsführer: Dieter Kaden (Vors.), Ralph Riedle, Jens Bergmann
Internet: http://www.dfs.de Public-Key der DFS: http://www.dfs.de/dfs/public_key.asc
Wow, what cheek. Why don't you save more time and ask us to write your report, too?
If you use an open source tool, you will need to dig out the facts yourself, and you will need to avoid asking "qualitative" questions (such as questions 2, 3, 4, 5, etc) and ask factual questions (like 1) that don't requirement a judgment call.
The vendors who offer tools usually have sales departments who will be happy to fill out your RFI forms.
GLH
From: Matthias.Anthes at dfs.de [mailto:Matthias.Anthes at dfs.de]
Sent: Wednesday, August 27, 2008 1:05 AM
To: hobbit at hswn.dk
Subject: [hobbit] Antwort: [hobbit] hobbit-clients.cfg not recognizing DISK /autoyast IGNORE
Dear ladies and gentlemen,
momentanely I´am working on a concept for monitoring tools which compares some montitoring tools in regard of the requirements of our company.
Can you tell me if the following requirements will be fulfilled by your tool?
(1) Open Source Solution
(2) Big community is available
(3) Documentation is at a high quality
(4) Tool is easy to operate
(5) The Tool configuration is easy
(6) HMI configuration is easy
(7) Background pictures can be implementet
(8) Support of SNMP v1,v2,v3
(9) It is possible to call scripts (shell scripts, perl scripts and so on)
(10) Definition of roles possible
(11) Processing of Traps possible
(12) Tool shall be extendable
(13) Longtime-monitoring shall be possible.
Please can you checkmark these items?
I create a list with a lot of features for the tools but unfortunately have some open points also for your tool BigSister.
So I would ask you if you can make checkmarks to the open features if your tool will fulfill the features.
Here they are:
1. Alert-Form (mail, SMS, pager,....)
2. History of generated Status changes displayable/archieveable
3. Logging and Display of Performance data
4. Protocolls (snmp, ssh,...)
5. HW support like VMWare, Cisco, Juniper, F5, Veritas, Nortel, EMC, NetApp...
6. Support of geographic network maps
7. redundancy by starting multiple instances possible
8. Real-time diagnosis
9. Local tests by installing application on a client
10. history and reports
11. flexibility: Def. of alarm thresholds and warning, HMI adaptable
12. User management
13. longterm monitoring
14. Availibility report
15. Virtualisation possible
16. Templates available
17. XML-Data-Import / Export
18. Application load distribution on multiple hosts
19. Integration of failure and performance monitoring
Can you return the answer to my e-mail-account please?
In hope of a quick answer I send you many regards,
I need this information urgently because I have to finish the concept on friday
Many regards,
DFS Deutsche Flugsicherung GmbH
Am DFS-Campus 10
D - 63225 Langen
Tel.: +49-(0)6103-707-0
Sitz der Gesellschaft: Langen/Hessen
Zuständiges Registergericht: AG Offenbach am Main, HRB 34977
Vorsitzender des Aufsichtsrates: Robert Scholl
Geschäftsführer: Dieter Kaden (Vors.), Ralph Riedle, Jens Bergmann
Internet: http://www.dfs.de
Public-Key der DFS: http://www.dfs.de/dfs/public_key.asc
participants (6)
-
etmsys@rit.edu
-
greg.hubbard@eds.com
-
Matthias.Anthes@dfs.de
-
rbrusletto@selero.com
-
rmcgraw@purdue.edu
-
skjoldar@gmail.com