Hi all
Can anybody point me to some documentation about how to use SPLITNCV. (Or perhaps you can answer my questions)
In the mailing list I have seen it as SPLITNCV, SPLIT_NCV and SPLIT-NCV. Which is it? As in, what goes into hobbitserver.cfg? What version of Xymon was it introduced? I can't seem to get it working here, so I might need an upgrade, or was this feature only ever delivered in a patch?
Regards Vernon
Here is a sample of how I use it.
SQLTPS = ncv
NCV_SQLTPS="Transactions:GAUGE"
This worked for me over several releases.
-----Original Message----- From: Vernon Everett [mailto:everett.vernon at gmail.com] Sent: 06 July 2010 08:40 AM To: hobbit at hswn.dk Subject: [hobbit] SPLITNCV
Hi all
Can anybody point me to some documentation about how to use SPLITNCV. (Or perhaps you can answer my questions)
In the mailing list I have seen it as SPLITNCV, SPLIT_NCV and SPLIT-NCV. Which is it? As in, what goes into hobbitserver.cfg? What version of Xymon was it introduced? I can't seem to get it working here, so I might need an upgrade, or was this feature only ever delivered in a patch?
Regards Vernon
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
Hi Neil
That's NCV, and it works a treat. Been using it for years. However, I am looking at the SPLITNCV feature.
It appears really cool on paper. I just need to make it work for me.
It will allow you to graph a previously unknown number of lines, by putting them one per rrd file instead of all into a single rrd file. You then generate the graphs using a wildcard in the rrd file definition in hobbitgraph.cfg.
But like i mentioned, on the trends page it looks great. On the test page, all the lines are on one graph. :-(
Cheers V
On Tue, Jul 6, 2010 at 2:57 PM, Neil Franken <nfranken at theunlimitedworld.co.za> wrote:
Here is a sample of how I use it.
SQLTPS = ncv
NCV_SQLTPS="Transactions:GAUGE"
This worked for me over several releases.
-----Original Message----- From: Vernon Everett [mailto:everett.vernon at gmail.com] Sent: 06 July 2010 08:40 AM To: hobbit at hswn.dk Subject: [hobbit] SPLITNCV
Hi all
Can anybody point me to some documentation about how to use SPLITNCV. (Or perhaps you can answer my questions)
In the mailing list I have seen it as SPLITNCV, SPLIT_NCV and SPLIT-NCV. Which is it? As in, what goes into hobbitserver.cfg? What version of Xymon was it introduced? I can't seem to get it working here, so I might need an upgrade, or was this feature only ever delivered in a patch?
Regards Vernon
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
OK. Did a little trial and error.
It's SPLITNCV_testname
And we use GRAPH to control the number of lines on a graph. GRAPH="blah blah,stuff,testname::4" This should give me 4 lines per graph in trends. It gives me 3 :-( testname::5 gives me the 4 lines I was looking for. Anybody else seen this behaviour?
Next question though. testname::X controls the number of lines on the trends page. How do I limit the number of lines on the actual testname page? Right now it's showing the lot on one graph, and it's mega fugly.
Regards Vernon
On Tue, Jul 6, 2010 at 2:40 PM, Vernon Everett <everett.vernon at gmail.com> wrote:
Hi all
Can anybody point me to some documentation about how to use SPLITNCV. (Or perhaps you can answer my questions)
In the mailing list I have seen it as SPLITNCV, SPLIT_NCV and SPLIT-NCV. Which is it? As in, what goes into hobbitserver.cfg? What version of Xymon was it introduced? I can't seem to get it working here, so I might need an upgrade, or was this feature only ever delivered in a patch?
Regards Vernon
participants (2)
-
everett.vernon＠gmail.com
-
nfranken＠theunlimitedworld.co.za