OK, this is a long shot, but... None of the other graph definitions have "-l 0" *after* the GPRINT lines... Dunno why that would make a difference, but you might want to either move it or just comment it out and bounce xymon to see what happens.
Ralph Mitchell
On Wed, May 25, 2011 at 2:39 PM, Nick Camaldi <willowbrookmagic at hotmail.com>wrote:
The plot thickens
i compiled this on production made all modifications
moved all my data over and everything works except for if_load and temp. devmon is pulling the data.
here are my rrddefinitons for the above.
[if_load] FNPATTERN if_load.(.*).rrd TITLE Network Traffic YAXIS Bits/second DEF:in at RRDIDX@=@RRDFN@:ds0:AVERAGE CDEF:inbytes at RRDIDX@=in at RRDIDX@,8,* DEF:out at RRDIDX@=@RRDFN@:ds1:AVERAGE CDEF:outbytes at RRDIDX@=out at RRDIDX@,8,* LINE1:inbytes at RRDIDX@#@COLOR@:@RRDPARAM@ In GPRINT:inbytes at RRDIDX@:LAST: %8.2lf %s (cur) GPRINT:inbytes at RRDIDX@:MAX: %8.2lf %s (max) GPRINT:inbytes at RRDIDX@:MIN: %8.2lf %s (min) GPRINT:inbytes at RRDIDX@:AVERAGE: %8.2lf %s (avg)\n LINE1:outbytes at RRDIDX@#@COLOR@:@RRDPARAM@ Out GPRINT:outbytes at RRDIDX@:LAST: %8.2lf %s (cur) GPRINT:outbytes at RRDIDX@:MAX: %8.2lf %s (max) GPRINT:outbytes at RRDIDX@:MIN: %8.2lf %s (avg) GPRINT:outbytes at RRDIDX@:AVERAGE: %8.2lf %s (avg)\n -l 0
[temp] FNPATTERN temp.(.*).rrd TITLE Temperature YAXIS Degrees Celsius DEF:in at RRDIDX@=@RRDFN@:ds0:AVERAGE DEF:out at RRDIDX@=@RRDFN@:ds1:AVERAGE LINE1:in at RRDIDX@#@COLOR@:@RRDPARAM@ Temperature GPRINT:in at RRDIDX@:LAST: %8.2lf %s (cur) GPRINT:in at RRDIDX@:MAX: %8.2lf %s (max) GPRINT:in at RRDIDX@:MIN: %8.2lf %s (min) GPRINT:in at RRDIDX@:AVERAGE: %8.2lf %s (avg)\n #LINE1:out at RRDIDX@#@COLOR@:@RRDPARAM@ Threshold #GPRINT:out at RRDIDX@:LAST: %8.2lf %s (cur) #GPRINT:out at RRDIDX@:MAX: %8.2lf %s (max) #GPRINT:out at RRDIDX@:MIN: %8.2lf %s (avg) #GPRINT:out at RRDIDX@:AVERAGE: %8.2lf %s (avg)\n -l 0
From: bgmilne at staff.telkomsa.net To: willowbrookmagic at hotmail.com Subject: Re: [Xymon] Devmon on Xymon 4.3.2 - if_load and temp issue for all devmon hosts Date: Wed, 25 May 2011 16:02:45 +0200
On Wednesday, 25 May 2011 15:24:27 Nick Camaldi wrote:
RRD files for If_load and temp for all devmon hosts are not working it shows a red x
So the graph definition was not available in your new Xymon configuration.
and not updating i try and remove rrd files for a host and it doesn't re-create.
No need to remove them ...
For this one, most likely your TEST2RRD does not contain the correct 'if_load=devmon' and 'temp=devmon' values, although these are defaults?
Regards, Buchan
Xymon mailing list Xymon at xymon.com http://lists.xymon.com/mailman/listinfo/xymon