thorsten.erdmann at daimler.com wrote:
Hi David
I just tested your template against my MGE Galaxy. There are some minor issues:
I developed it against a Chloride UPS.
- battery voltage is displayed as 42100V, yeah. I solved that with setting the transform of "upsBatteryVoltageTxt" to "{upsBatteryVoltage} / 10" instead of "x 10" Whoops - my bad. My UPS shows: UPS-MIB::upsBatteryVoltage.0 (.1.3.6.1.2.1.33.1.2.5.0) = INTEGER: 22 0.1 Volt DC So that's really 2.2V not 220V.
- battery current is 0A, it seems that the MGE does not deliver this value Likewise, my UPS does not return anything other than 0. We just had a power failure and it didn't even move from 0 during that, so it's not drain on the batteries when in use. It was really there for completeness.
- message test is yellow: "primary OID upsAlarmDescrTxt in table is a non-repeater", I don't know how to solve that Rest assured, when there IS an alarm, you will see them - I had 2 this morning.
At the moment devmon doesn't handle empty repeaters well. I had some discussions with Buchan a while ago.
- output power is 0kW. If I use the special MGE MIB I get real results I do get real values on output power (but not on input power).
- input power displays unrealistic results: Line bads: 3 Input configuration: 3 lines of 0 V AC @ 0.0 Hz
These depend on config values. They may need to be populated in the UPS management interface - I'm not sure. I do get them returned for my UPS.
UPS Input Phase Freq Volts Amps Power 1 50.0 Hz 390V 28.0A 2746W 2 50.0 Hz 395V 28.0A 2835W 3 50.0 Hz 391V 28.0A 2765W
- I am missing some temperature tests
So now I am unsure what to do. I can ignore these issues I can modify your template to use the OIDs of the vendor's MIB I can use my own template which does not display so much results, but uses the vendor's MIB
I've had similar dilemmas with HP servers with all kinds of mixes of hardware RAID controllers, hardware event logs and then adding SNMP-Informant on the top.
It seems that the vendors does not support the standard UPS MIB very cleanly. So I think we have to build a special template for every vendor. :-(
But even if I don't use your template it was very helpful. It is a very good demonstration how to use tables and other stuff in devmon. I didn't try the graphing now, but I will do it now. :-)
Let me know how you go with that.
Thank you for your work!!!
Thanks.
I just added "templatebuilder.pl" into the extras directory in the devmon SVN repository.
It gives a good start on putting together a template, translating between names and OIDs, generating barebones oids, transforms and thresholds files.
It relies on having the MIB definition files installed correctly.
David.
Thorsten
david.baldwin at ausport.gov.au schrieb am 11.09.2009 07:26:30:
My UPS template has been tweaked and is now available from the devmon SF repository: http://devmon.svn.sourceforge.net/viewvc/devmon/trunk/templates/ups. tar.gz?view=tar
README file includes hobbitgraph.cfg section and info on setting up RRD collection and graphing.
Let me know if any problems. The msgs test attempts to show the AlarmDesc repeater which is empty unless there are any alarms which may cause issues - I've increased the number of "not found" repeaters slightly in my copy of devmon to be more lenient. The line is in modules/dm_snmp.pm
if($failed_query > 2) {
I increased 2 to 6.
your example was very helpfull. I now managed to get a working devmon template for my MGE UPS. Only graphing isn't working now.
BTW.: anyone knows how I can format output numbers in devmon. I now get the voltages with two digits behind the colon, but these are always zero. So I want to omit these digits at all.
The number of decimal digits displayed is controlled in the transforms file with MATH operator by adding ": N" - e.g.
upsInputCurrentA : MATH : {upsInputCurrent} / 10 : 1
will display for example 10.1 - change to ": 0" to get 10
David.
Thorsten Erdmann
david.baldwin at ausport.gov.au schrieb am 10.09.2009 09:51:49:
Sorry all, didn't get time today to update the UPS template today.
It has separate graphs for input voltage, output phase voltages,
battery
levels and separate tests/alerting on various conditions - input voltage=0, battery time remaining <15 mins, output phase overload, etc.
David.
Oops, forgot to add the graphing bit.
Usual stuff. In hobbitserver.cfg Add "ups=ncv" to TEST2RRD= Add "ups" to GRAPHS= Add line NCV_ups="Load:GAUGE,Charge:GAUGE"
Add this to hobbitgraph.cfg [ups] TITLE UPS Charge YAXIS Power -u 100 -l 0 DEF:u=ups.rrd:Charge:AVERAGE DEF:p=ups.rrd:Load:AVERAGE LINE2:u#00CC00:Charge LINE2:p#0000FF:Load COMMENT:\n GPRINT:u:LAST:Charge \: %5.1lf%s (cur) GPRINT:u:MAX: \: %5.1lf%s (max) GPRINT:u:MIN: \: %5.1lf%s (min) GPRINT:u:AVERAGE: \: %5.1lf%s (avg)\n GPRINT:p:LAST:Load \: %5.1lf%s (cur) GPRINT:p:MAX: \: %5.1lf%s (max) GPRINT:p:MIN: \: %5.1lf%s (min) GPRINT:p:AVERAGE: \: %5.1lf%s (avg)\n Cheers Vernon
*From:* Everett, Vernon [mailto:Vernon.Everett at woodside.com.au] *Sent:* Thursday, 10 September 2009 2:50 PM *To:* 'hobbit at hswn.dk' *Subject:* RE: [hobbit] Antwort: RE: [hobbit] UPS monitoring using devmon
I wrote this a while back for our MGEs. As you can see, it predates my introduction to devmon and indicates a complete lack of understanding of SNMP. That being said, the code and the MIBs might give you a good indication of where to start. (Either that, or you can just use it as "good enough") This was designed to run on the hobbit/xymon server.
I have been meaning to rewrite this, or move it to devmon, but just haven't had the time. (And it's doing an adequate job for now.)
Cheers V
bb-host entries look like this 1.2.3.4 galaxy3000 # http://1.2.3.4/ups_prop.htm ups galaxy3000 COMMENT:"Meaningful Comment if required" 2.3.4.5 Karratha_UPS # http://2.3.4.5/ups_prop.htm ups galaxy3000 COMMENT:"Insert Comment"
--- snip---
cat ups.ksh #!/bin/ksh DATE=$(date) #set -x SPACER="
" BBTMP=/tmp #BBHOSTS=/etc/hobbit/bb-hosts #OUT=$BBTMP/upspage BBHOSTLIST="$BBHOSTS $(grep ^include $BBHOSTS | awk '{ print $2 }')" # Make sure we read the include files too #grep -h " ups " $BBHOSTLIST | egrep -v "^page|^include" grep -h " ups " $BBHOSTLIST | egrep -v "^page|^include" | while read IP UPSNAME HASH URL UPS TYPE OTHER do echo $IP $UPSNAME ping -c1 $IP > /dev/null if [ $? -eq 0 ] then COLOUR=green case $TYPE in galaxy3000) > $OUT.warn > $OUT.tmp TEMP=$(snmpget -v1 -c public $IP SNMPv2-SMI::mib-2.33.1.1.1.0) DEVICE=${TEMP##*:} # String TEMP=$(snmpget -v1 -c public $IP SNMPv2-SMI::mib-2.33.1.1.2.0) MODEL=${TEMP##*:} # String TEMP=$(snmpget -v1 -c public $IP SNMPv2-MIB::sysLocation.0) LOCATION=${TEMP##*:} # String TEMP=$(snmpget -v1 -c public $IP SNMPv2-SMI::mib-2.33.1.1.4.0) SERIAL=${TEMP##*:} # String TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.4.8.0) LOWBATTERY=${TEMP##*:} # Integer % Point at which shutdown triggered TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.5.1.0) TIME_REMAIN=${TEMP##*:} # Integer seconds TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.5.2.0) BATTERY_LEVEL=${TEMP##*:} # Integer % TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.5.9.0) BATTERY_FAULT=${TEMP##*:} # Integer 1=yes 2=no TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.5.11.0) BATTERY_REPLACE=${TEMP##*:} # Integer 1=yes 2=no TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.5.15.0) CHARGER_FAULT=${TEMP##*:} # Integer 1=yes 2=no TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.3.0) OUT_ON_BAT=${TEMP##*:} # Integer 1=yes 2=no TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.4.0) OUT_ON_BYPASS=${TEMP##*:} # Integer 1=yes 2=no TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.10.0) OUT_OVERLOAD=${TEMP##*:} # Integer 1=yes 2=no TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.10.0) COMMSOK=${TEMP##*:} # Integer 1=yes 2=no TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.6.1.0) INPHASES=${TEMP##*:} # Integer 1 or 3
TEMP=$(snmpget -v1 -c public $IP1.3.6.1.4.1.705.1.6.2.1.2) INVOLT=${TEMP##*:} # Integer 10ths of a volt
TEMP=$(snmpget -v1 -c public $IP1.3.6.1.4.1.705.1.6.2.1.3) INFREQ=${TEMP##*:} # Integer 10ths of a Hertz
TEMP=$(snmpget -v1 -c public $IP1.3.6.1.4.1.705.1.6.2.1.6) INAMPS=${TEMP##*:} # Integer 10ths of an Amp
TEMP=$(snmpget -v1 -c public $IP1.3.6.1.4.1.705.1.6.3.0) INOK=${TEMP##*:} # Integer 1=yes 2=no TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.6.4.0) INFAILCAUSE=${TEMP##*:} # Integer 1=no fault # 2=bad voltage # 3=bad frequency # 4=no voltage TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.1.0) OUTPHASES=${TEMP##*:} # Integer 1 or 3 TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.2.1.2) OUTVOLT=${TEMP##*:} # Integer 10ths of a volt TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.2.1.3) OUTFREQ=${TEMP##*:} # Integer 10ths of a Hertz TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.2.1.4) OUTLOAD=${TEMP##*:} # Integer % TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.2.1.5) OUTAMPS=${TEMP##*:} # Integer 10ths of an Amp TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.11.0) OVERTEMP=${TEMP##*:} # Integer 1=yes 2=no echo "Manufacturer
"$DEVICE | sed 's/"//g' >> $OUT.tmp echo "Model "$MODEL | sed 's/"//g' >> $OUT.tmp echo "Serial Number
"$SERIAL | sed 's/"//g' >> $OUT.tmp echo "Location
"$LOCATION | sed 's/"//g' >> $OUT.tmp echo >> $OUT.tmp #$LOWBATTERY #WARN="" #[ -z "$TIME_REMAIN" ] && TIME_REMAIN=0 #[ $TIME_REMAIN -lt 1200 -a "$COLOUR" != "red" ] && COLOUR=yellow #[ $TIME_REMAIN -lt 1200 ] && WARN="Time Remaining low" #[ $TIME_REMAIN -lt 600 ] && COLOUR=red #[ $TIME_REMAIN -lt 600 ] && WARN="Time Remaining critical" #[ "$WARN" != "" ] && echo $WARN >> $OUT.warn ((s=$TIME_REMAIN%60)) ((m=$TIME_REMAIN/60)) echo "Time Remaining "$m Minutes $s Seconds >> $OUT.tmp WARN="" [ -z "$BATTERY_LEVEL" ] && BATTERY_LEVEL=0 [ $BATTERY_LEVEL -lt 95 -a "$COLOUR" != "red" ] && COLOUR=yellow [ $BATTERY_LEVEL -lt 95 ] && WARN="Battery level low" [ $BATTERY_LEVEL -lt 50 ] && COLOUR=red [ $BATTERY_LEVEL -lt 50 ] && WARN="Battery level critical" [ "$WARN" != "" ] && echo $WARN >> $OUT.warn echo "Battery Level
"$BATTERY_LEVEL % >> $OUT.tmp BATTERY_LEVEL=$(echo $BATTERY_LEVEL | sed 's/[ \t]*//') if [ $BATTERY_FAULT -eq 1 ] then BF=Yes COLOUR=red echo "Battery Fault!" >> $OUT.warn else BF=No fi echo "Battery Fault "$BF >> $OUT.tmp if [ $BATTERY_REPLACE -eq 1 ] then BR=Yes COLOUR=red echo "Battery replacement required" >> $OUT.warn else BR=No fi echo "Replace Battery "$BR >> $OUT.tmp if [ $BATTERY_FAULT -eq 1 ] then BR=Yes COLOUR=red echo "Battery replacement required" >> $OUT.warn else BR=No fi if [ $CHARGER_FAULT -eq 1 ] then CF=Yes COLOUR=red echo "Charger Fault" >> $OUT.warn else CF=No fi echo "Charger Fault "$CF >> $OUT.tmp if [ $OUT_ON_BAT -eq 1 ] then OUT_ON_BAT=Yes COLOUR=red echo "UPS running on battery" >> $OUT.warn else OUT_ON_BAT=No fi echo "On Battery
"$OUT_ON_BAT> $OUT.tmp if [ $OUT_ON_BYPASS -eq 1 ] then OUT_ON_BYPASS=Yes COLOUR=red echo "UPS on power bypass" >> $OUT.warn else OUT_ON_BYPASS=No fi echo "On Bypass
"$OUT_ON_BYPASS >> $OUT.tmp if [ $OUT_OVERLOAD -eq 1 ] then OUT_OVERLOAD=Yes COLOUR=red echo "UPS output overload" >> $OUT.warn else OUT_OVERLOAD=No fi echo "Battery Overload
"$OUT_OVERLOAD > $OUT.tmp if [ $OVERTEMP -eq 1 ] then OVERTEMP=Yes COLOUR=red echo "Unit overheating" >> $OUT.warn else OVERTEMP=No fi echo "Unit Overheating
"$OVERTEMP >> $OUT.tmp #if [ $COMMSOK -eq 2 ] #then # COMMSOK=No # COLOUR=red # echo "No comms from device" >> $OUT.warn #else # COMMSOK=Yes #fi #echo "Comms OK
"$COMMSOK >> $OUT.tmp echo >> $OUT.tmp echo "Input Phases
"$INPHASES >> $OUT.tmp INVOLT=$(echo "scale=1 ; $INVOLT/10" | bc) echo "Input Voltage
"$INVOLT >> $OUT.tmp INFREQ=$(echo "scale=1 ; $INFREQ/10" | bc) echo "Input Frequency
"$INFREQ >> $OUT.tmp INAMPS=$(echo "scale=1 ; $INAMPS/10" | bc) echo "Input Current
"$INAMPS >> $OUT.tmp if [ $INOK -eq 1 ] then # A silly case of reverse logic applies here INOK=No COLOUR=red echo "Power input outside tollerance" >> $OUT.warn else INOK=Yes fi echo "Input OK "$INOK >> $OUT.tmp [ $INFAILCAUSE -eq 1 ] && FAILCAUSE="No failures" [ $INFAILCAUSE -eq 2 ] && FAILCAUSE="Voltage out of tollearance" [ $INFAILCAUSE -eq 3 ] && FAILCAUSE="Frequency out of tollernace" [ $INFAILCAUSE -eq 4 ] && FAILCAUSE="No voltage - power fail" echo "Cause of Failure
"$FAILCAUSE >> $OUT.tmp echo >> $OUT.tmp echo "Output Phases
"$OUTPHASES >> $OUT.tmp OUTVOLT=$(echo "scale=1 ; $OUTVOLT/10" | bc) echo "Output Voltage
"$OUTVOLT >> $OUT.tmp OUTFREQ=$(echo "scale=1 ; $OUTFREQ/10" | bc) echo "Output Frequency
"$OUTFREQ >> $OUT.tmp OUTAMPS=$(echo "scale=1 ; $OUTAMPS/10" | bc) echo "Output Current
"$OUTAMPS >> $OUT.tmp OUTLOAD=$(echo $OUTLOAD | sed 's/[ \t]*//') echo "Output Load
"$OUTLOAD % >> $OUT.tmp echo >> $OUT.final cat $OUT.warn >> $OUT.final cat $OUT.tmp >> $OUT.final echo '<FONT COLOR="Black">' >> $OUT.final echo "Load=$OUTLOAD" >> $OUT.final echo "Charge=$BATTERY_LEVEL" >> $OUT.final echo '</FONT>' >> $OUT.final rm $OUT.tmp rm $OUT.warn esac else echo "Device Unreachable!" >> $OUT.final #COLOUR=yellow fi $BB $BBDISP "status $UPSNAME.ups $COLOUR $DATE $(cat $OUT.final)" rm $OUT.final done--- snip ---
*From:* thorsten.erdmann at daimler.com [mailto:thorsten.erdmann at daimler.com] *Sent:* Thursday, 10 September 2009 2:18 PM *To:* hobbit at hswn.dk *Subject:* [hobbit] Antwort: RE: [hobbit] UPS monitoring using devmon
Hi Craig, hi David,
sounds very nice.
I tried that snmpwalk. It only works with snmp V1. This is the output:
SNMPv2-SMI::mib-2.33.1.1.1.0 = STRING: "MGE UPS SYSTEMS" SNMPv2-SMI::mib-2.33.1.1.2.0 = STRING: "Galaxy PW Single//" SNMPv2-SMI::mib-2.33.1.1.3.0 = "" SNMPv2-SMI::mib-2.33.1.1.4.0 = STRING: "GB (SN 49EE49044)" SNMPv2-SMI::mib-2.33.1.1.5.0 = "" SNMPv2-SMI::mib-2.33.1.1.6.0 = ""
As I see it, this is only the description of the UPS. I will look for the MIB of my devices. Don't know where all the other things which I want to monitor at minimum are located in the MIB like:
Overall status or am I runnung on battery output power remaining battery time temperature
I'll look at uploading it to the SF repository. Maybe this is a stupid question, but I don't find templates and things on the SF page. Only devmon itself. I look at http://devmon.sourceforge.net/ and at http://sourceforge.net/projects/devmon/ There is a devmon-template file there, but as I see it, it contains only the templates which are delivered with devmon itself.
It would be nice if you share your templates. You can also contact me via EMail at thorsten.erdmann at daimler dot com
Thank you very much
Thorsten
Craig
-----Original Message----- From: David Baldwin [mailto:david.baldwin at ausport.gov.au] Sent: Thursday, 10 September 2009 11:53 AM To: hobbit at hswn.dk Subject: Re: [hobbit] UPS monitoring using devmon
thorsten.erdmann at daimler.com wrote: > > Hi, > > sorry if this a little offtopic, but maybe someone has a
devmon
> template for the following UPS: > > Emerson/Liebert HiPulse MM > MGE Galaxy Single > MGE Upsilon STS_100 Cross switch > MGE Upsilon STS_20 Cross switch > > Thank you > Thorsten > > > If you are not the intended addressee, please inform us immediately > that you have received this e-mail in error, and delete it. We thank > you for your cooperation. > I have a template for the standard UPS MIB which I could send through. I have a little more work to do on it splitting the power status into 3 tests for input, output and battery. Should give me motivation to complete this today and I will upload to devmon SF site.
You can check if your UPS supports the standard UPS MIB or wants a proprietary one (substituting for myups below, and your community string if it is not "public"):
snmpwalk -v2c -cpublic myups 1.3.6.1.2.1.33.1.1
Note that some UPS devices only support SNMPv1, so try -v1 instead of -v2c above if it doesn't work.
David.
-- David Baldwin - IT Unit Australian Sports Commission www.ausport.gov.au Tel 02 62147830 Fax 02 62141830 PO Box 176 Belconnen ACT 2616 david.baldwin at ausport.gov.au Leverrier Street Bruce ACT 2617
Keep up to date with what's happening in Australian sport visit http://www.ausport.gov.au
This message is intended for the addressee named and may contain confidential and privileged information. If you are not the intended recipient please note that any form of distribution, copying or use of this communication or the information in it is strictly prohibited and may be unlawful. If you receive this message in error, please delete it and notify the sender.
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
DISCLAIMER:
The information contained in this email message is confidential and for the attention of the intended recipient only. It is not necessarily the official view or communication of the Rodney District Council. If you are not the intended recipient you must not disclose, copy or distribute this message or the information in it. If you have received this message in error, please delete or destroy all copies of the email and notify the sender immediately. Rodney District Council accepts no responsibility for any effects this email message or attachments has on the recipient network or computer system.
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
If you are not the intended addressee, please inform us immediately that you have received this e-mail in error, and delete it. We thank you for your cooperation.
NOTICE: This email and any attachments are confidential. They may contain legally privileged information or copyright material. You must not read, copy, use or disclose them without authorisation. If you are not an intended recipient, please contact us at once by return email and then delete both messages and all attachments.
NOTICE: This email and any attachments are confidential. They may contain legally privileged information or copyright material. You must not read, copy, use or disclose them without authorisation. If you are not an intended recipient, please contact us at once by return email and then delete both messages and all attachments.
-- David Baldwin - IT Unit Australian Sports Commission www.ausport.gov.au Tel 02 62147830 Fax 02 62141830 PO Box 176 Belconnen ACT 2616 david.baldwin at ausport.gov.au Leverrier Street Bruce ACT 2617
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
If you are not the intended addressee, please inform us immediately that you have received this e-mail in error, and delete it. We thank you for your cooperation.
-- David Baldwin - IT Unit Australian Sports Commission www.ausport.gov.au Tel 02 62147830 Fax 02 62141830 PO Box 176 Belconnen ACT 2616 david.baldwin at ausport.gov.au Leverrier Street Bruce ACT 2617
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
If you are not the intended addressee, please inform us immediately that you have received this e-mail in error, and delete it. We thank you for your cooperation.