I wrote this a while back for our MGEs. As you can see, it predates my introduction to devmon and indicates a complete lack of understanding of SNMP. That being said, the code and the MIBs might give you a good indication of where to start. (Either that, or you can just use it as "good enough") This was designed to run on the hobbit/xymon server.
I have been meaning to rewrite this, or move it to devmon, but just haven't had the time. (And it's doing an adequate job for now.)
Cheers V
bb-host entries look like this 1.2.3.4 galaxy3000 # http://1.2.3.4/ups_prop.htm ups galaxy3000 COMMENT:"Meaningful Comment if required" 2.3.4.5 Karratha_UPS # http://2.3.4.5/ups_prop.htm ups galaxy3000 COMMENT:"Insert Comment"
--- snip---
cat ups.ksh #!/bin/ksh DATE=$(date) #set -x SPACER=" " BBTMP=/tmp #BBHOSTS=/etc/hobbit/bb-hosts #OUT=$BBTMP/upspage BBHOSTLIST="$BBHOSTS $(grep ^include $BBHOSTS | awk '{ print $2 }')" # Make sure we read the include files too #grep -h " ups " $BBHOSTLIST | egrep -v "^page|^include" grep -h " ups " $BBHOSTLIST | egrep -v "^page|^include" | while read IP UPSNAME HASH URL UPS TYPE OTHER do echo $IP $UPSNAME ping -c1 $IP > /dev/null if [ $? -eq 0 ] then COLOUR=green case $TYPE in galaxy3000) > $OUT.warn > $OUT.tmp TEMP=$(snmpget -v1 -c public $IP SNMPv2-SMI::mib-2.33.1.1.1.0) DEVICE=${TEMP##*:} # String TEMP=$(snmpget -v1 -c public $IP SNMPv2-SMI::mib-2.33.1.1.2.0) MODEL=${TEMP##*:} # String TEMP=$(snmpget -v1 -c public $IP SNMPv2-MIB::sysLocation.0) LOCATION=${TEMP##*:} # String TEMP=$(snmpget -v1 -c public $IP SNMPv2-SMI::mib-2.33.1.1.4.0) SERIAL=${TEMP##*:} # String TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.4.8.0) LOWBATTERY=${TEMP##*:} # Integer % Point at which shutdown triggered TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.5.1.0) TIME_REMAIN=${TEMP##*:} # Integer seconds TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.5.2.0) BATTERY_LEVEL=${TEMP##*:} # Integer % TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.5.9.0) BATTERY_FAULT=${TEMP##*:} # Integer 1=yes 2=no TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.5.11.0) BATTERY_REPLACE=${TEMP##*:} # Integer 1=yes 2=no TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.5.15.0) CHARGER_FAULT=${TEMP##*:} # Integer 1=yes 2=no TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.3.0) OUT_ON_BAT=${TEMP##*:} # Integer 1=yes 2=no TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.4.0) OUT_ON_BYPASS=${TEMP##*:} # Integer 1=yes 2=no TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.10.0) OUT_OVERLOAD=${TEMP##*:} # Integer 1=yes 2=no TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.10.0) COMMSOK=${TEMP##*:} # Integer 1=yes 2=no TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.6.1.0) INPHASES=${TEMP##*:} # Integer 1 or 3
TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.6.2.1.2)
INVOLT=${TEMP##*:} # Integer 10ths of a volt
TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.6.2.1.3)
INFREQ=${TEMP##*:} # Integer 10ths of a Hertz
TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.6.2.1.6)
INAMPS=${TEMP##*:} # Integer 10ths of an Amp
TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.6.3.0)
INOK=${TEMP##*:} # Integer 1=yes 2=no
TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.6.4.0)
INFAILCAUSE=${TEMP##*:} # Integer 1=no fault
# 2=bad voltage
# 3=bad frequency
# 4=no voltage
TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.1.0)
OUTPHASES=${TEMP##*:} # Integer 1 or 3
TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.2.1.2)
OUTVOLT=${TEMP##*:} # Integer 10ths of a volt
TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.2.1.3)
OUTFREQ=${TEMP##*:} # Integer 10ths of a Hertz
TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.2.1.4)
OUTLOAD=${TEMP##*:} # Integer %
TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.2.1.5)
OUTAMPS=${TEMP##*:} # Integer 10ths of an Amp
TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.11.0)
OVERTEMP=${TEMP##*:} # Integer 1=yes 2=no
echo "Manufacturer "$DEVICE | sed 's/"//g' >> $OUT.tmp
echo "Model "$MODEL | sed 's/"//g' >> $OUT.tmp
echo "Serial Number "$SERIAL | sed 's/"//g' >> $OUT.tmp
echo "Location "$LOCATION | sed 's/"//g' >> $OUT.tmp
echo >> $OUT.tmp
#$LOWBATTERY
#WARN=""
#[ -z "$TIME_REMAIN" ] && TIME_REMAIN=0
#[ $TIME_REMAIN -lt 1200 -a "$COLOUR" != "red" ] && COLOUR=yellow
#[ $TIME_REMAIN -lt 1200 ] && WARN="Time Remaining low"
#[ $TIME_REMAIN -lt 600 ] && COLOUR=red
#[ $TIME_REMAIN -lt 600 ] && WARN="Time Remaining critical"
#[ "$WARN" != "" ] && echo $WARN >> $OUT.warn
((s=$TIME_REMAIN%60))
((m=$TIME_REMAIN/60))
echo "Time Remaining "$m Minutes $s Seconds >> $OUT.tmp
WARN=""
[ -z "$BATTERY_LEVEL" ] && BATTERY_LEVEL=0
[ $BATTERY_LEVEL -lt 95 -a "$COLOUR" != "red" ] && COLOUR=yellow
[ $BATTERY_LEVEL -lt 95 ] && WARN="Battery level low"
[ $BATTERY_LEVEL -lt 50 ] && COLOUR=red
[ $BATTERY_LEVEL -lt 50 ] && WARN="Battery level critical"
[ "$WARN" != "" ] && echo $WARN >> $OUT.warn
echo "Battery Level "$BATTERY_LEVEL % >> $OUT.tmp
BATTERY_LEVEL=$(echo $BATTERY_LEVEL | sed 's/[ \t]*//')
if [ $BATTERY_FAULT -eq 1 ]
then
BF=Yes
COLOUR=red
echo "Battery Fault!" >> $OUT.warn
else
BF=No
fi
echo "Battery Fault "$BF >> $OUT.tmp
if [ $BATTERY_REPLACE -eq 1 ]
then
BR=Yes
COLOUR=red
echo "Battery replacement required" >> $OUT.warn
else
BR=No
fi
echo "Replace Battery "$BR >> $OUT.tmp
if [ $BATTERY_FAULT -eq 1 ]
then
BR=Yes
COLOUR=red
echo "Battery replacement required" >> $OUT.warn
else
BR=No
fi
if [ $CHARGER_FAULT -eq 1 ]
then
CF=Yes
COLOUR=red
echo "Charger Fault" >> $OUT.warn
else
CF=No
fi
echo "Charger Fault "$CF >> $OUT.tmp
if [ $OUT_ON_BAT -eq 1 ]
then
OUT_ON_BAT=Yes
COLOUR=red
echo "UPS running on battery" >> $OUT.warn
else
OUT_ON_BAT=No
fi
echo "On Battery "$OUT_ON_BAT >> $OUT.tmp
if [ $OUT_ON_BYPASS -eq 1 ]
then
OUT_ON_BYPASS=Yes
COLOUR=red
echo "UPS on power bypass" >> $OUT.warn
else
OUT_ON_BYPASS=No
fi
echo "On Bypass "$OUT_ON_BYPASS >> $OUT.tmp
if [ $OUT_OVERLOAD -eq 1 ]
then
OUT_OVERLOAD=Yes
COLOUR=red
echo "UPS output overload" >> $OUT.warn
else
OUT_OVERLOAD=No
fi
echo "Battery Overload "$OUT_OVERLOAD >> $OUT.tmp
if [ $OVERTEMP -eq 1 ]
then
OVERTEMP=Yes
COLOUR=red
echo "Unit overheating" >> $OUT.warn
else
OVERTEMP=No
fi
echo "Unit Overheating "$OVERTEMP >> $OUT.tmp
#if [ $COMMSOK -eq 2 ]
#then
# COMMSOK=No
# COLOUR=red
# echo "No comms from device" >> $OUT.warn
#else
# COMMSOK=Yes
#fi
#echo "Comms OK "$COMMSOK >> $OUT.tmp
echo >> $OUT.tmp
echo "Input Phases "$INPHASES >> $OUT.tmp
INVOLT=$(echo "scale=1 ; $INVOLT/10" | bc)
echo "Input Voltage "$INVOLT >> $OUT.tmp
INFREQ=$(echo "scale=1 ; $INFREQ/10" | bc)
echo "Input Frequency "$INFREQ >> $OUT.tmp
INAMPS=$(echo "scale=1 ; $INAMPS/10" | bc)
echo "Input Current "$INAMPS >> $OUT.tmp
if [ $INOK -eq 1 ]
then
# A silly case of reverse logic applies here
INOK=No
COLOUR=red
echo "Power input outside tollerance" >> $OUT.warn
else
INOK=Yes
fi
echo "Input OK "$INOK >> $OUT.tmp
[ $INFAILCAUSE -eq 1 ] && FAILCAUSE="No failures"
[ $INFAILCAUSE -eq 2 ] && FAILCAUSE="Voltage out of tollearance"
[ $INFAILCAUSE -eq 3 ] && FAILCAUSE="Frequency out of tollernace"
[ $INFAILCAUSE -eq 4 ] && FAILCAUSE="No voltage - power fail"
echo "Cause of Failure "$FAILCAUSE >> $OUT.tmp
echo >> $OUT.tmp
echo "Output Phases "$OUTPHASES >> $OUT.tmp
OUTVOLT=$(echo "scale=1 ; $OUTVOLT/10" | bc)
echo "Output Voltage "$OUTVOLT >> $OUT.tmp
OUTFREQ=$(echo "scale=1 ; $OUTFREQ/10" | bc)
echo "Output Frequency "$OUTFREQ >> $OUT.tmp
OUTAMPS=$(echo "scale=1 ; $OUTAMPS/10" | bc)
echo "Output Current "$OUTAMPS >> $OUT.tmp
OUTLOAD=$(echo $OUTLOAD | sed 's/[ \t]*//')
echo "Output Load "$OUTLOAD % >> $OUT.tmp
echo >> $OUT.final
cat $OUT.warn >> $OUT.final
cat $OUT.tmp >> $OUT.final
echo '<FONT COLOR="Black">' >> $OUT.final
echo "Load=$OUTLOAD" >> $OUT.final
echo "Charge=$BATTERY_LEVEL" >> $OUT.final
echo '</FONT>' >> $OUT.final
rm $OUT.tmp
rm $OUT.warn
esac
else
echo "Device Unreachable!" >> $OUT.final
#COLOUR=yellow
fi
$BB $BBDISP "status $UPSNAME.ups $COLOUR $DATE $(cat $OUT.final)"
rm $OUT.finaldone
--- snip ---
From: thorsten.erdmann at daimler.com [mailto:thorsten.erdmann at daimler.com] Sent: Thursday, 10 September 2009 2:18 PM To: hobbit at hswn.dk Subject: [hobbit] Antwort: RE: [hobbit] UPS monitoring using devmon
Hi Craig, hi David,
sounds very nice.
I tried that snmpwalk. It only works with snmp V1. This is the output:
SNMPv2-SMI::mib-2.33.1.1.1.0 = STRING: "MGE UPS SYSTEMS" SNMPv2-SMI::mib-2.33.1.1.2.0 = STRING: "Galaxy PW Single//" SNMPv2-SMI::mib-2.33.1.1.3.0 = "" SNMPv2-SMI::mib-2.33.1.1.4.0 = STRING: "GB (SN 49EE49044)" SNMPv2-SMI::mib-2.33.1.1.5.0 = "" SNMPv2-SMI::mib-2.33.1.1.6.0 = ""
As I see it, this is only the description of the UPS. I will look for the MIB of my devices. Don't know where all the other things which I want to monitor at minimum are located in the MIB like:
Overall status or am I runnung on battery output power remaining battery time temperature
I'll look at uploading it to the SF repository. Maybe this is a stupid question, but I don't find templates and things on the SF page. Only devmon itself. I look at http://devmon.sourceforge.net/ and at http://sourceforge.net/projects/devmon/ There is a devmon-template file there, but as I see it, it contains only the templates which are delivered with devmon itself.
It would be nice if you share your templates. You can also contact me via EMail at thorsten.erdmann at daimler dot com
Thank you very much
Thorsten
Craig
-----Original Message----- From: David Baldwin [mailto:david.baldwin at ausport.gov.au] Sent: Thursday, 10 September 2009 11:53 AM To: hobbit at hswn.dk Subject: Re: [hobbit] UPS monitoring using devmon
thorsten.erdmann at daimler.com wrote:
Hi,
sorry if this a little offtopic, but maybe someone has a devmon template for the following UPS:
Emerson/Liebert HiPulse MM MGE Galaxy Single MGE Upsilon STS_100 Cross switch MGE Upsilon STS_20 Cross switch
Thank you Thorsten
If you are not the intended addressee, please inform us immediately that you have received this e-mail in error, and delete it. We thank you for your cooperation.
I have a template for the standard UPS MIB which I could send through. I have a little more work to do on it splitting the power status into 3 tests for input, output and battery. Should give me motivation to complete this today and I will upload to devmon SF site.
You can check if your UPS supports the standard UPS MIB or wants a proprietary one (substituting for myups below, and your community string if it is not "public"):
snmpwalk -v2c -cpublic myups 1.3.6.1.2.1.33.1.1
Note that some UPS devices only support SNMPv1, so try -v1 instead of -v2c above if it doesn't work.
David.
-- David Baldwin - IT Unit Australian Sports Commission www.ausport.gov.au Tel 02 62147830 Fax 02 62141830 PO Box 176 Belconnen ACT 2616 david.baldwin at ausport.gov.au Leverrier Street Bruce ACT 2617
Keep up to date with what's happening in Australian sport visit http://www.ausport.gov.au
This message is intended for the addressee named and may contain confidential and privileged information. If you are not the intended recipient please note that any form of distribution, copying or use of this communication or the information in it is strictly prohibited and may be unlawful. If you receive this message in error, please delete it and notify the sender.
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
DISCLAIMER:
The information contained in this email message is confidential and for the attention of the intended recipient only. It is not necessarily the official view or communication of the Rodney District Council. If you are not the intended recipient you must not disclose, copy or distribute this message or the information in it. If you have received this message in error, please delete or destroy all copies of the email and notify the sender immediately. Rodney District Council accepts no responsibility for any effects this email message or attachments has on the recipient network or computer system.
To unsubscribe from the hobbit list, send an e-mail to hobbit-unsubscribe at hswn.dk
If you are not the intended addressee, please inform us immediately that you have received this e-mail in error, and delete it. We thank you for your cooperation.
NOTICE: This email and any attachments are confidential. They may contain legally privileged information or copyright material. You must not read, copy, use or disclose them without authorisation. If you are not an intended recipient, please contact us at once by return email and then delete both messages and all attachments.